User Manual

Motion Sensor 360 (Flush Mount)
SKU: PP-SNS-MOTION-F

Table of Contents

1. Dimensions

Image
  • H: 39 mm
  • W1: 52 mm
  • W2: 40 mm
Image

There is a jumper position behind the open terminal, direct jumper to select normally open or normally closed.

  1. Default Normal Open

Normal Open: When sensing someone the relay engages (outputs a signal): Relay disconnected when unmanned (no signal output)

Normal Close: When there is no one present, the relay is engaged (output signal): Relay disconnected when sensing someone (no signal output)

2. Detection angel

Image
  1. 100°
  2. 360°
  3. 3-6 m

3. Installation

Image
  1. Choose an appropriate height - 3 meters recommended
Image
  1. Ceiling
  2. Put the motion sensor in the hole
  3. Opening hole with a diameter of 41-45 mm on the ceiling

4. Wiring

Image
  • Connect the Line (L) wire to terminal L on the sensor.
  • Connect the Neutral (N) wire directly to terminal N on the sensor.
  • Connect the Load (device) wire to the sensor's output terminal.

5. Add the Motion sensor to the App

Image
  1. Choose Controller
    1. Tap on the Controller that you would like to add new I/O to.
    2. To edit the I/O, click on the Controller to which the I/O is added.
Image
  1. Add button for Inputs
    1. Inputs tab is selected.
    2. List of Inputs is shown.
    3. In order to add new Input tap on the Add button.
Image
  1. Choose type - Inputs
    1. Scroll to the I/O from the list that you would like to add and tap on it.
Image
  1. New Motion sensor
    1. Fill following form:
      1. Name - Write the name of the Motion sensor.
      2. Role - Choose Role from the list.
      3. Group - Choose Group from the list. Group is a group of I/O and scenarios that seems most logical to you.
      4. Pin - Choose Pin from the list. Pin is physical place on the Controller where I/O is connected to it.
      5. Photo - Choose photo for the Motion sensor.
      6. Identifier - This field is the identifier of the I/O in the electrical project.
      7. Advanced - You can choose type of the signal that activates or triggers the Motion sensor: rising, falling, change, change inverted.
      8. Timeout - It the duration for which the Motion sensor will remain active in auto mode.

When you want to confirm your choice tap button Save and Submit.

Image
  1. Select Roles - Inputs
    1. Tap in the field Roles.
    2. Select checkbox/checkboxes (for multiple choice) next to the Role/Roles that you would like to choose.
    3. To confirm selection tap the button Save/Done.
Image
  1. Select Groups - Inputs
    1. In this step you should select Group.
    2. Select check box/check boxes next to the desired Group/Groups from the list.
    3. When you want to confirm your choice tap button Done/Save.
Image
  1. Change photo
    1. Tap on the photo of the Motion sensor.
    2. You have tree options:
      1. Open Library - The phone’s Library will open.
      2. Open Camera - You can take a picture using your smartphone.
      3. Choose default image - These images are prepared in advance in order  to provide a complete and seamless experience.
Image
  1. Timeout
    1. In order to set Timeout - hours, minutes and seconds, you should scroll through each of these columns and when you are satisfied with your choice tap on Save button.
Image
  1. Advanced Configuration
    1. Select radio button next to the Signal that you would like to choose:
      1. Rising
      2. Failing
      3. Change
      4. Change inverted
    2. It is a type of signal that activates or triggers the Motion sensor.

© 2024 Pierre. All rights reserved.

Last updated: September 09, 2025